TPS-200
- 9-5/8 in
- 7-5/8 in
- 7 in
- 5-1/2 in
- 5 in
- 4-1/2 in
- 2-7/8 in
- 2-3/8 in
Pull needed up to 400,000 lb.
Rev E design values
Pull needed up to 400,000 lb.
Rev E design values
10-3/4 in casing, or pull needed over 400,000 lb and up to 800,000 lb on any listed size.
Rev B design values, preliminary
A size not listed, or pull needed over 800,000 lb.
Spec a jack| Specification | TPS-200 Rev E design values | TPS-400 Rev B design values, preliminary |
|---|---|---|
| Model | TPS-200 | TPS-400 |
| Design pull (lb) | 400,000 | 800,000 |
| Pull (short tons) | 200 | 400 |
| Revision | Rev E design values | Rev B design values, preliminary |
| Pull | 200 short tons (400,000 lb; 1,779 kN) at 3,537 psi on a 4,000 psi power unit | 400 short tons (800,000 lb; 3,559 kN) at 4,527 psi on a 5,000 psi power unit |
| Parts designed for | Parts designed for 5,000 psi; relief set at 200 short tons | Parts designed for 6,000 psi; relief set at 400 short tons |
| Proof test | 250 short tons (1.25 times the design pull), each unit | 500 short tons (1.25 times the design pull), each unit |
| Stroke | 48 in; fast mode to 139 short tons | 48 in; two speeds (4 or 2 cylinders) |
| Stroke speed | About 53 in/min; about 76 in/min fast | About 56 in/min; about 112 in/min fast |
| Clearance | 12.25 in (passes a 9-5/8 coupling) | 13.25 in (passes a 10-3/4 coupling) |
| Height, lowered / raised | 74 / 122 in (jack only) | 79 / 127 in (jack only) |
| Wellhead spool options | 13-5/8 3M standard, cellar bridge | 13-5/8 3M, 13-5/8 5M, 11 in 3M, 11 in 5M |
| Spool height | 15.5 in | 14 in |
| Base / head width | 44 / 41 in | 51 / 48 in |
| Weight | About 6,500 lb jack; about 1,300 lb spool | About 10,800 lb jack; about 1,700 lb spool |
| Master bowls | 9-5/8 in | 10-3/4 in, 9-5/8 in |
| Insert bowls | 7-5/8 in, 7 in, 5-1/2 in, 5 in, 4-1/2 in, 2-7/8 in, 2-3/8 in | 7-5/8 in, 7 in, 5-1/2 in, 5 in, 4-1/2 in, 2-7/8 in, 2-3/8 in |
| Slip sizes | 9-5/8 in, 7-5/8 in, 7 in, 5-1/2 in, 5 in, 4-1/2 in, 2-7/8 in, 2-3/8 in | 10-3/4 in, 9-5/8 in, 7-5/8 in, 7 in, 5-1/2 in, 5 in, 4-1/2 in, 2-7/8 in, 2-3/8 in |
| Bowl | adapter bowl | insert bowls |
| Power unit | 4,000 psi, about 26 gpm, 85 to 100 hp, air shutoff | 5,000 psi, about 43 gpm, 150 to 200 hp |
| Load holding | Counterbalance valve on each cylinder | Pilot-operated check; velocity fuse on each cylinder |
| Overpressure | Rod relief on each cylinder; crush-limited relief | Lockable relief set per string; rod-side relief |
| Controls | Dead-man lever at a remote stand; slip retainers | Dead-man lever at a remote control stand |
| Work floor | Traveling work floor option | Not offered on the TPS-400 |
| Cylinder hydro test | 7,500 psi, each cylinder | 7,500 psi, each cylinder |
Design values. The jack is not rated or certified until a licensed PE has stamped the design and the unit has passed its proof test. Pull on any string is limited by the operating relief to 80% of pipe body yield (TPS-200: also limited by slip-crush capacity). The wellhead, a cellar bridge or bearing mats must carry the full reaction load.